Wait a second!
More handpicked essays just for you.
More handpicked essays just for you.
Rate of reaction thiosulfate and hydrochloric acid
Rate of reaction thiosulfate and hydrochloric acid
Investigating the concentration of sodium thiosulfate
Don’t take our word for it - see why 10 million students trust us with their essay needs.
Recommended: Rate of reaction thiosulfate and hydrochloric acid
The Rate of Reaction Between Sodium Thiosulphate and Hydrochloric Acid
Theory:
Sodium thiosulphate and hydrochloric acid, react together to produce
sulphur as one of the products
Na2S2O3 (aq) + 2HCl (aq)
Sodium Thiosulphate + Hydrochloric acid
à
2NaCl (aq) + H2O (l) + S (s) + SO2 (g)
Sodium Chloride + Water + Sulphur + Sulphur Dioxide
Sulphur is a yellow precipitate, so the solution will turn an opaque
yellow colour while the reaction is occurring. The reaction will
continue and eventually the solutionwill turn completely opaque.
Aim: - the aim of this experiment is to show the effect on the rate of
reaction, when the concentration of one of the reagents changes.
Variables
Dependant Variable: -Variable that is measured. This will be the time,
from when the HCl is added to the Na2S2O3, until the solution goes
yellow and opaque, when a cross, which is written on a label placed
underneath the reaction, can not be see.
Independent Variable: - Variable that is changed. This will be the
concentration of Na2S2O3.
Controlled variable: - There are four variables that may affect the
experiment and the results.
These are concentration and volume of HCl, the same person with the
stopwatch, the same apparatus, temperature these could all affect the
results.
I. Concentration and volume of HCl : - If the concentration is
increased then the number of particles in the solution increases. If
this happens then the number of collisions will increase, and
therefore the number of successful collisions will increase. This is
because the more particles of HCl, then there are more collisions;
therefore the collision frequency is higher. Therefore increasing the
successful collision frequency.
II.The same person with the stopwatch: - The person using the
stopwatch has to stay the same because each person has their own
reaction time, so if another person were to start at the same point,
they could be slower or faster, it would be unlikely that two
different people would have the same reaction time.
Input variables In this experiment there are two main factors that can affect the rate of the reaction. These key factors can change the rate of the reaction by either increasing it or decreasing it. These were considered and controlled so that they did not disrupt the success of the experiment. Temperature-
How am I going to make it a fair test I will use a clean flask for
The results of this experiment are shown in the compiled student data in Table 1 below.
Yorkston, K. M., Hammen, V. L., Beukelman, D. R., & Traynor, C. D. (1990). The effect of rate
Rate of Reaction Between Calcium Carbonate and Hydrochloric Acid Plan: In my experiment I will measure the rate of reaction between calcium carbonate and hydrochloric acid. The rate of the reaction is the speed that the reaction takes place so by measuring the rate I will measure the amount of time the reaction takes. Hydrochloric acid is a strong acid that is found in digestive juices in the stomach, it is also used for cleaning metals before they are coated. Calcium carbonate has a few forms including chalk and limestone the main use of these two materials is in the making of concrete, which is used for many things such as buildings. When you put calcium carbonate and hydrochloric acid together they react to form calcium chloride, carbon dioxide and water.
Going into details of the article, I realized that the necessary information needed to evaluate the experimental procedures were not included. However, when conducting an experiment, the independent and dependent variable are to be studied before giving a final conclusion.
The Rate of Reaction Between Calcium Carbonate and Hydrochloric Acid Planning. CaCO3 (s) + 2HCl (aq) ---- CaCl2 (aq) + H2O (l) + CO2 The rate of reaction depends on how hard and how often the reacting particles collide with each other. A rate of reaction is how fast a reaction takes place.
from 10cm to 50cm to make it easier to see the difference in a graph.
take about 30 minutes for the water to cool down 20ºC, which is why I
Rate of Reaction - Sodium Thiosulphate and Hydrochloric Acid. Aim Investigation, to find out how the rate of reaction between sodium thiosulphate and hydrochloric acid is affected by changing the concentration. Introduction I must produce a piece of coursework investigating the rate of reaction, and the effect different changes have on them. The rate of reaction is the rate of loss of a reactant, or the rate of development of a product during a chemical reaction. It is measured by dividing 1 by the time taken for the reaction to take place.
Effect of Temperature on the Rate of Reaction between Sodium Thiosulphate and Hydrochloric Acid Investigation Chemical reactions are used in our everyday life, they literally keep us alive. They are used in food, respiration and everywhere else in the environment. A chemical reaction mainly occurs when reactants react together to produce a new product. The speed at which this reaction takes place is called the rate of reaction. The product produced has a number of particles in the solution that has formed from the reactants.
Investigating the Effects of Temperature on the Rate of Reaction between Magnesium and Hydrochloric Acid
a bigger one so I can fit the cross under it and also be able to pour
Hydrochloric Acid, Sodium Thiosulphate Reaction. Research: What is the difference between Hydrochloric acid is a strong colourless acid formed when hydrogen chloride gas dissociates in water, used in industrial and laboratory. processes. The.
There is also the potential of human error within this experiment for example finding the meniscus is important to get an accurate amount using the graduated pipettes and burettes. There is a possibility that at one point in the experiment a chemical was measured inaccurately affecting the results. To resolve this, the experiment should have been repeated three times.