The center column was the first part of the packed tower, put up it is fill with plastic, it was held up by plastic able ties. The water and air packed towers, filled with resin beads inside of them, held up with plastic cable ties. The air packed column was connected to the center packed column with medium length nipple and an elbow joint connected a copper pipe to a thin silicon pipe. At the same time a silicon pipe, attached to the air packed column, was connected to the air valve, and with a small nipple a control valve and flowmeter are attached. Then a small nipple attached to the flowmeter is connected to the pressure gauges where attached to the air packed tower. The center column had two thick silicone pipes each connected to an elbow joint, the elbow joints were each then connected to a small nipple, the two nipples connected to a t-shaped joint. The t-shaped joint was connected to a nipple that was later connected to a union. The union had a small nipple attached, the nipple was then also attached to an elbow joint, the elbow joint connected with a long copper rod. The copper rod was attached to an elbow joint, the elbow joint was attached to a nipple, which was attached to another elbow joint, to a nipple that was attached to the top of water packed column. …show more content…
The open nipple end of the union was attached to a t-shaped joint, one end of the left side of the t-shaped joint was connected to a shut-off valve by a nipple, and a silicon pipe, to release excess water, by a small nipple. At the bottom of the t-shaped joint a flow meter gauge was attached, along with a flow meter and control valve below by two small nipples connecting them. The small nipple is connected to a long nipple attached to a silicon pipe to the water valve. The pressure gauges were then attached to the water packed
Compress the safety bulb, hold it firmly against the end of the pipette. Then release the bulb and allow it to draw the liquid into the pipette.
Vessel formation begins as Maria flattens a ball of clay. She places the flattened clay onto the puki, supporting base,
3. Using a graduated cylinder, measure and pour 5 ml of the CaCl solution into a test tube and use a utility clamp to fasten the test tube to
A. It is a fluid screen that is generated by pumping water through a screen nozzle and having an axial flow director and a nozzle insert on it.
We attached a gas syringe via a plastic tube to a test tube and used a
Two pipes were attached together, one with a length of slightly over 50cm and a radius of 5cm, and a pipe receptor near the bottom of the pipe. Both ends of the pipe were open, but the end nearest the receptor was securely covered with a pipe cap, as shown in Figure 1. The receptor was also open. The second pipe consisted of a thin metal pipe with a length of 1 metre, which was attached to another pipe cap, which was pierced through the middle, as shown in Figure 2. This allowed water to flow through the output
It was a megalithic structure and represented a large organization of labor and engineering due to the size and weight of the supports and blocks that were used in its creation. There were two types of stones used in the construction, the larger sarsen and the smaller bluestones (Greaney). “The sarsen blocks weigh up to 50 tons a piece, and traveled 200 miles”, indicate the difficulty in moving the stone (Davies 18). What now appears to be a unified design actually happened in four parts. During the middle of the period that it was built, the structure “had grown into a horseshoe-shaped arrangement of five sarsen triliths, encircled by a ring of upright blocks capped with lintel” (Davies16).
The picture itself is not exemplary of any one classical Greek building, but contains many elements of classical Greek architecture and design. The columns are what stand out the most in the architecture of this picture. The original Greek columns came in three different styles, or orders: Doric, Ionic, and Corinthian. All Greek columns consist of both a shaft and a capital, and sometimes there is a base as well. The shaft is made from round drums stacked one on top of the other. The main difference among the orders comes from the differences in the capitals. The Doric capitals are usually very simple and look like the weight of the roof is flattening them out. The Ionic capitals are a little fancier with a large volute, which looks like rams horns rolling off of the shaft. The Corinthian capital is much more complex with smaller volutes and many stylized acanthus leaves and rosettes, accompanied by a boss on the top of each side. All three types of columns rest on the floor of the building, which is often a temple. The fl...
Explain in detail about the design and operation of packed distillation column, giving its design equations in terms of NTU and HTU.
A process flow diagram of the pump system is shown in Figure 1. The main components of the system are a centrifugal pump with a 4½-inch impeller, a 2-horsepower motor, a piping system with an effective length of about 285 feet, a rotameter for low liquid flow rates (0-2 gpm), a magnetic flow meter for high liquid flow rates (0-90 gpm), and a tank.
where L_(make-up) is the mass flow rate of the water from the make-up tank, G_inlet is the mass flow rate of air at the inlet, H_inlet is the humidity of the air at its inlet, G_outlet is the mass flow rate of air at the outlet, and H_outlet is the humidity of the air at its outlet. The amount of make-up water needed for the system can be calculated by determining the loss of water due to evaporation. Using a mass balance of the air flow in tower, the mass flow rate of the water loss, L_loss, can be represented by,
(a) A rain gauges (b) A wind vane (c) An anemometer (d) A hygrometer (e) hydrometer
Columns form (Fig.3b) is a cylindrical tube made of flat rectangular sheets of fabric. It can be supported from above by scaffolding or along a rigid vertical joint [5]. Columns form is used for the construction of columns or vertical structures through custom and architectural profile.
Octagonal pods was formed with cylinders underneath for support. The black metal gleamed from every angle holding a uption society dream inside it like a cage. It was built in a secluded surrounding where fences rose as high as the hopes of creating the structure itself. May 25, 2025 the structure was going to take flight into an innovative mankind I knew I would be destined spot on the Raft. My mother worked in the translation department for days on end. Coffee rings formed on the magnoy wood of her desk and bags under her eyes looked as if someone had socked her. I felt as if everything began to fall into place for once.