Introduction Scuba diving itself can be challenging at times. Imagine having a difficult task, like welding, to perform at the same time as scuba diving. This is a task that can cost you your life if not done correctly and as safely as possible. There are two types of careers that allow welders the opportunity to weld and dive. One career is offshore underwater welding (offshore) and the other is inland underwater welding (inland). Although offshore underwater welding has more job opportunities than inland underwater welding, offshore pays slightly higher and has more benefits than inland. Those are not the only two variables though, you also have to think about which is more dangerous, and which wears your body down more. Last, which will keep you away from family and friends? Offshore exhausts the body Inland underwater welders mostly work year round and offshore underwater welders work 8 …show more content…
Such as the Deepwater Horizon Incident that occurred on April 20, 2010 of the Gulf of Mexico. When working in pipelines offshore welders are working under the risk of getting sucked into one of the pipes from the immense pressure they would be working under. The Deepwater Horizon Incident, also referred to as the BP Oil Spill or BP Oil Disaster , was considered the largest accidental marine oil spill in which eleven people went missing and were never found. The reason this was such a catastrophe was because the oil rig in which this occurred on was about 40 miles away and was not reached by the Coast Guard in time for the fire to be extinguished or prevented from getting bigger. When working offshore you will also be working in pipelines where there is the risk of you getting sucked into one of those from the immense pressure you would be working
Deep water and strong currents could lead to drowning. - stay away from the sea.
Career Education Advisor states that welding is relatively dangerous work, done in some potentially hazardous environments. Welders work with electrical currents, large machinery, and heavy parts in conditions that include factories and construction sites. Management-level welders spend time on work sites as well as in the office (Career Education Advisor). Finally, every occupation has advantages
Throughout this essay we have had a chance to look at the two major types of underwater diving. We have a better understanding of the differences in the equipment used, the locations that each may be performed, and the career opportunities available to a person with the proper credentials.
Welding is a excellent career choice for those who like to build things with their hands and have a strong attention to detail. It requires an extensive amount of knowledge and skill but for those who get a solid grasp of the respected trade they're rewarded with tremendous job opportunities and first-rate pay.
Divers cannot put the equipment on and immediately dive in. Before diving there are a series of procedures the diver and their partners must do before going down. In addition, the further down the diver dives the more pressure pressing down on the diver which lessens the amount of oxygen in the scuba tank. Therefore, the further down the diver dives the less time the diver can spend on the bottom. But now, by far the largest group of divers is “Recreational Divers”. These dives are practiced at depths of less than 130 feet, from these depths, divers can make a straight ascent to the surface. Diving beyond this limit requires advanced training. Also, when diving the diver must take into account the amount of time spent descending and ascending in the water. If the diver descends too quickly the pressure can deflate their lungs and cause problems. Similarly, if they ascend too quickly nitrogen bubbles can form under the diver’s skin causing bends or decompression sickness. This sickness can be extremely harmful and possibly fatal. Lastly, a dive watch or computer is needed to calculate the amount of oxygen left in their tank and the depth. Dive computers help the divers be aware of their conditions and keep them
Scuba diving is an activity enjoyed by people all over the world. Scientists use it to study underwater life, police use it to train in case of emergencies, and many others do it just for fun. What many people don't know, though, is that scuba diving would be impossible without physics. Pressure, buoyancy, and force are big parts of diving.
Diving has gotten away from the stereotype based on the early days of diving, that it is a rough and tough sport requiring extreme endurance and strength. Today it is viewed as an activity done by both men and women and even children. While diving is promoted as a leisure sport, it is still a sport. One that takes an amount of physical activity. We start by carrying heavy tanks on our backs. We are in constant motion for the entire dive. Even breathing is a more difficult as we must overcome the additional pressure on our body as we expand our chest.
In rare occurrences workplace injury leads to death while the majority of injuries are minor. The national OHS strategy 2002-2012 by the Australian government has set a target to reduce fatality rate by 20% over the decade. The data from Safe Work Australia statistical report 2009-2010, shows a 10% decrease over 5 years to 2008, an increase in 2009 and a decrease in 2010 (Graph 1). The increase in 2008-2009 was among 15-24 years age group with 95% being male workers.
On April 20, 2010, the Deepwater Horizon oil rig, located in the Gulf of Mexico, exploded, killing 11 workers and injuring 17. The oil rig sank a day and a half later. The spill was referred to as the Deepwater Horizon oil spill, BP oil spill, Gulf of Mexico oil spill, and BP oil disaster. It was first said that little oil had actually leaked into the ocean, but a little over a month later the estimate was 12,000-19,000 barrels of crude oil being leaked per day. Many attempts were made to stop the leak but all failed until they capped the leak on July 15, 2010, and on September 19 the federal government declared the well “effectively dead.”
Workplace safety is a commonly used phrase that many do not consider until an accident occurs within the workplace. Throughout the U.S., workplace injuries occur on a daily basis. This has been an issue in the workforce for many years and is still an ongoing issue. Are there laws that protect employees from an unsafe work environment; what is the Occupational Safety and Health Act (OSHA); and how did the labor unions affect the law? In this paper these following questions will be addressed, as well as the background and driving force of OSHA.
Many people think of scuba diving as just a swim in the water, but in reality it is a very exciting, dangerous, and potentially fatal sport and activity. There are many types of scuba diving, ranging from recreational to sport to career diving. Scuba Diving is just not a swim in the water, scuba requires certification, uses technical equipment, and there is a lot of risk involved with scuba diving.
When outdoors, they may work on a scaffold or platform high off the ground. They may have to lift heavy objects and work in awkward positions while bending, stooping, or standing to work overhead. Welders are exposed to a number of hazards including very hot materials and the intense light created by the arc. They wear safety shoes, heat resistant gloves, goggles, masks with protective lenses, and other equipment to prevent burns and eye injuries and to protect them from falling objects. They also work in safely ventilated areas in order to avoid danger from inhaling gases and fine particles that can result from welding processes. Because of these hazards, welders have a rate of injuries and illness that is higher than the national average. Most welders work full time and work overtime. Many firms have two or three eight to twelve hour shifts each day. As a result welders may work evenings, nights, and even
Welding is an art, science, and high paying career all in one. Welding is the most effective way to join two pieces of metal, it is the only way to join them so they act as one. Numerous things in our daily lives has been welded from coffeepots to skyscrapers. Welding can be done almost anywhere outdoors, indoors, underwater, and even space (“Welding Basics”). It is practically
The very first scuba dives performed were in search for jewelry and very short until a way to breathe underwater for longer periods of time was invented. In order for the divers to stay submerged underwater longer, they used a hollow reed. Research shows that later on, “helmets were made of metal to withstand even greater water pressure and divers went deeper” (MarineBio.org 1). These improvements in technology gave divers a smoother dive, allowing them to enjoy more time submerged deeper in the ocean. Along with divers being able to stay under longer and enjoy the underwater sea life, there came some dangers that were not recognized and are potentially serious if one does not take diving serious.
Moreover, it also require participants to have a great body, because they need to stay underwater for a long time. (The top five scuba diving destinations in the United States are Key Largo, Florida; Maui, Hawaii; Big Island, Hawaii; Florida Spring; Kauai, Hawaii.)