BROMINATION OF BENZENE
SYNTHESIS AND PURIFICATION OF BROMOBENZENE: PROCEDURE
DATA TABLE
Chemical Boiling point C Melting Point C Density g/mL Solubility
Benzene 80.1 5.5 0.88 Slightly in H2O
Toluene 110.6 -93 0.87 Slightly in H2O
Bromobenzene 155-156 -30.8 1.50 Insoluble
Dibromobenzene 220.40 87.31 0.96 Insoluble
MATERIALS:
Graduated cylinder
Weight scale
Buchner funnel
Filter flask
Rubber stopper
Hot plate
Thermometer
Conical funnel
Various size beakers
Fractionating column (for reflux)
Various sized round bottom flasks
Distillation head
Condenser
Vacuum adapter
Clamps and stands
Test tubes
PROCEDURE:
Pre Lab:
The experiment should be carried out AWAY from the sunlight. Before beginning the experiment, we need to make sure that the benzene used in the experiment is free of toluene and water. To do this, we must put anhydrous calcium chloride into a flask o...
Then the reaction tube was capped but not tightly. The tube then was placed in a sand bath reflux to heat it until a brown color was formed. Then the tube was taken out of the sand bath and allowed to cool to room temperature. Then the tube was shaken until a formation of a white solid at the bottom of the tube. After formation of the white solid, diphenyl ether (2 mL) was added to the solution and heated until the white solid was completely dissolved in the solution. After heating, the tube was cooled to room temperature. Then toluene (2 mL) was added to the solution. The tube was then placed in an ice bath. Then the solution was filtered via vacuum filtration, and there was a formation of a white solid. Then the product was dried and weighed. The Final product was hexaphenylbenzene (0.094 g, 0.176 mmol,
This experiment was conduct to investigate the fluorescent behaviour of Leucophor PAF and to investigate the quenching of QBS with NaCl. It was found that the Leucophor PAF indeed satisfied the characteristic to act as whitening agent. It was also found that the quenching of QBS with NaCl was a diffusion-controlled collision process.
At this point the identity of the unknown compound was hypothesized to be calcium nitrate. In order to test this hypothesis, both the unknown compound and known compound were reacted with five different compounds and the results of those reactions were compared. It was important to compare the known and unknown compounds quantitatively as well to ensure that they were indeed the same compound. This was accomplished by reacting them both with a third compound which would produce an insoluble salt that could be filte...
For this experiment we have to use physical methods to separate the reaction mixture from the liquid. The physical methods that were used are filtration and evaporation. Filtration is the separation of a solid from a liquid by passing the liquid through a porous material, such as filter paper. Evaporation is when you place the residue and the damp filter paper into a drying oven to draw moisture from it by heating it and leaving only the dry solid portion behind (Lab Guide pg. 33.).
Input variables In this experiment there are two main factors that can affect the rate of the reaction. These key factors can change the rate of the reaction by either increasing it or decreasing it. These were considered and controlled so that they did not disrupt the success of the experiment. Temperature-
In our experiment we utilized the hydrate cobaltous chloride. Hydrates are crystalline compounds in which one or more molecules of water are combined with each unit of a salt. Cobalt (II) chloride hexahydrate is an inorganic compound which is a deep rose color in its hydrated form. As an inducer of
The purpose of this lab was to calculate the percent composition by mass of oxygen in potassium chlorate.
MTBE, or methyl tertiary butyl ether, is an oxygenate commonly used in gasoline in America, Europe, and other countries throughout the world. It is a compound created by the chemical reaction of methanol and isobutylene that is added to gasoline because of its high octane level, allowing gasoline to reach the required octane levels and still include a gasoline component. In addition, because it is an oxygenate, MTBE helps gasoline more fully combust, which increases performance and reduces the amount of harmful pollutants such as CO, VOCs, NOx, and particulates released into the atmosphere from automobile exhaust [EFOA]. However, opposition has recently arisen against the use of MTBE in gasoline.
We thank the University of Oklahoma and the chemistry faculty for providing the space, instructions, and equipment for the development of this report and experiment.
People have often pondered the reasons for the greatness of Edith Wharton's novel, Ethan Frome. What is it that causes this story to be considered an all-time American classic? One journalist quotes a humanities professor at MIT who states that, "We turn to Wharton because the truths she tells are a bracing tonic in a culture steeped in saccharine sentimentality." The journalist goes on to describe the typical, "popular" story and how they often have endings where "romantic ideals are magically fulfilled..." There is much more to Ethan Frome than simply an unhappy ending to contrast with the many other stories that have sugar-coated and sanguine endings. At first glance, the ending of Ethan Frome may appear to be only depressing. In truth, Wharton offers the reader a complex ending through the careful incorporation of poetic justice and irony.
Experiment #1: The purpose of this experiment is to investigate the effects of baking soda and light intensity on the rate of photosynthesis of green spinach leave through the observation of floating disk.
Hydrochloric acid + calcium carbonate arrow calcium chloride + carbon dioxide + water. HCl(aq) + CaCO3(s) arrow CaCl2(aq) + CO2(g) + H2O(l) Things that affect the reaction rate of this experiment are: 1. The temperature of the hydrochloric acid. 2.
The Effect of Temperature on the Rate of Reaction Between Hydrochloric Acid and Calcium Carbonate
Ensure gloves are worn at all times when handling strong acids and bases within the experiment of the preparation of benzocaine. 4-aminobenzoic acid (3.0g, 0.022 moles) was suspended into a dry round-bottomed flask (100cm3) followed by methylated sprits (20 cm3). Taking extra care the concentrated sulphuric acid of (3.0 cm3, 0.031 moles) was added. Immediately after the condenser was fitted on, and the components in the flask were swirled gently to mix components. It should be ensured that the reactants of the concentrated sulphuric acid and the 4-aminobenzoic acid were not clustered in the ground glass joint between the condenser itself and the flask. In order to heat the mixture to a boiling point, a heating mantle was used and then further left for gently refluxing for a constituent time of forty minutes. After the duration of the consistent forty minutes the rou...
Toluene hydrodealkylation or hydrodealkylation of toluene (HDA) is a process that used to produce benzene. The reaction occurs as: