In light with the modern industries, steel has been discovered to be the central supporting part of most manufacturing industries or production industries. Steel is a relatively cheap and versatile material used in the production of about every kind of good or machinery, and because of this steel is vital in the modern style of living and for the economic well-being. Additionally, because of the essential functions played by steel in general economic and infrastructural development, the steel industry on the other hand has often been considered as an indicative for prowess of an economy.
Steel can be categorised or called an alloy that is made up of mostly irons and has carbon content with the weight ranging from 0.2% and 2.1% (C:1000–10,8.67Fe), though varies with the grade. In line with this, an alloy is said to be an incomplete or complete solid solution of a single or additional elements in a metallic matrix. Single solid phase microstructure are given by whole firm solution of alloys, while the partial solution give two or more stages of development and perhaps homogeneous in giving out depending on heat treatment (thermal) study of the past events. Similarly, the properties of Alloy usually vary from that of the component elements and the constituents of Alloys are usually measured by mass.
Jones and Michael (1986, 1992) in their research found that Carbon on the other hand, is the most widely found or used alloying material for iron, though; manganese, vanadium, tungsten and chromium are some of the various other alloying elements used in the production of steel. The prevention of the displacements in the iron atom crystal lattice from moving by sliding past one another is due to the action of the hardening agents, hence ...
... middle of paper ...
...nished product.
Consequently, the semi-finished products will either have or be shaped like a rectangle cross-section which is called slab or it will have an equilateral rectangle shape cross-section known as blooms or billets. Further to this, the slabs or the billets or blooms are now processed and shaped to form the finished product, because the semi-finished products are undergoes a total process of transformation, or they are rolled into stylish and graceful container or products. This process of transformation is called hot rolling and it’s a way whereby they go through heat treatment. However, the hot-rolled rectangular broad flat thin piece is afterwards, turning over and over at a temperature that is ambient and this process is called the cold rolling. After, going through all these processes, an anti-corrosion protective material will be used to coat it.
We use metals to construct all kinds of structures, from bridges to skyscrapers to elevators. The strength as well as durability of materials that are crafted out of metal make the materials ideal not only for construction but also for many other applications.
The high temperature application of Austenitic Stainless Steel is somewhat limited because at higher temperatures it undergoes a phenomenon called Sensitization. According to Ghosh et al. [1], it refers to the precipitation of carbides and nitrides at the grain boundaries. Precipitation of Chromium rich carbides (Cr23C6) and nitrides at the grain boundaries result when the Austenitic stainless steel is heated and held in the temperature range of 500-8500C (773K-1123K). This precipitation of carbides taking place at the grain boundary is because of their insolubility at these temperature ranges. This leads to Chromium depreciated regions around the grain boundaries. So the change in microstructure is takes place and the regions with low Chromium contents become susceptible to Intergranular Corrosion (IGC) and Intergranular Stress Corrosion Cracking (Alvarez et al.) [1, 2]. Along with carbides and nitrides there is formation of chi phase. The chi phase, which is a stable intermetallic compound, consists of Fe, Cr, and Mo of type M18C. Some studies reveal that sensitization may lead to formation of Martensite. In addition to the altered microstructure, mechanical properties of the Austenitic Stain...
For decades, the steel industry has been one of the toughest markets on a global scale with most steel corporations ending up in bankruptcy. Foreign and domestic competitors, management issues, environmental issues, political agenda’s and technology have had much to do with the demise and more so of the success of the steel industry. The issues that this case focus on Nucor Corporation was of:
In the Wall Street Journal article titled, “Industry Cuts Back As Steel Prices Fall,” writer Robert Guy Matthews discusses recent changes in the price of steel in the U.S. He also discusses past and potential future influences on U.S. steel prices. These influences include the domestic supply and demand of steel as well as foreign supply and demand in the global market. Supply and demand have been mainly shaped by the recession at large.
Hoerr, J. P. (1988). And the wolf finally came : the decline of the American steel industry. Pittsburgh, PA: University of Pittsburgh Press.
The extraordinary power of the steel industry to shape the life of its communities and the people in them remain...
-Developed and implemented strip casting overseas to eliminate a step in the steel making process
How does the development of steel affect the development of civilizations?Steel is one of the biggest thing why this world is unequal because it was going to make doing jobs easy for everyone. In new guinea, they really couldn't make steel because it was too rainy and they spending all their time getting and making sago.So they didnt have time to have any specialist
By adding up to 2%,of carbon it makes the steel tough and strong. Although it’s tough and strong, it is able to bend. To make sure that the metal doesn’t rust, it has a zinc coating on it. Iron is 26 on the periodic table,and considered an “transition metal,” meaning that it is ductile and malleable, and conduct electricity and heat. ... “Some other elements that are similar to iron are cobalt and nickel. They are the only elements known to produce a magnetic field.” Zinc is 30 on the periodic table and it is also a transition metal like iron. “The first iron used by humans is likely to have come from meteorites.” A meteorite is a meteor that survives its passage through the earth's atmosphere such that part of it strikes the ground. More than 90 percent of meteorites are of rock, while the remainder consist wholly or partly of iron and nickel. Meteors are believed to have been from the asteroid belt of Mars and
Aluminum is a lightweight, silvery metal. The atomic weight of aluminum is 26.9815; the element melts at 660° C (1220° F), boils at 2467° C (4473° F), and has a specific gravity of 2.7. Aluminum is a strongly electropositive metal and extremely reactive. In contact with air, aluminum rapidly becomes covered with a tough, transparent layer of aluminum oxide that resists further corrosive action. For this reason, materials made of aluminum do not tarnish or rust. The metal reduces many other metallic compounds to their base metals. For example, when thermite (a mixture of powdered iron oxide and aluminum) is heated, the aluminum rapidly removes the oxygen from the iron; the heat of the reaction is sufficient to melt the iron. This phenomenon is used in the thermite process for welding iron .
This paper will first discuss the development of the steel industry. Next, it will examine steel, and in the impact it had on the transportation industry. Finally, it will discuss systematic management practices of this time and how they gave birth to the scientific approach that is still in use today.
The industrial revolution began in Europe in the 18th century. The revolution prompted significant changes, such as technological improvements in global trade, which led to a sustained increase in development between the 18th and 19th century. These improvements included mastering the art of harnessing energy from abundant carbon-based natural resources such as coal. The revolution was economically motivated and gave rise to innovations in the manufacturing industry that permanently transformed human life. It altered perceptions of productivity and understandings of mass production which allowed specialization and provided industries with economies of scale. The iron industry in particular became a major source of economic growth for the United States during this period, providing much needed employment, which allowed an abundant population of white people as well as minorities to contribute and benefit from the flourishing economy. Steel production boomed in the U.S. in the mid 1900s. The U.S. became a global economic giant due to the size of its steel industry, taking advantage of earlier innovations such as the steam engine and the locomotive railroad. The U.S. was responsible for 65 percent of steel production worldwide by the end of the 2nd World War (Reutter 1). In Sparrows Point: Making Steel: the Rise and Ruin of American Industrial Might, Mark Reutter reports that “Four out of every five manufacturing items contained steel and 40 percent of all wage earners owed their livelihood directly or indirectly to the industry.” This steel industry was the central employer during this era.
BIBLIOGRAPHY Advantages to Aluminum. http://www.kaiserextrusion.com/advantage.html. November 28, 2000. Aluminum Facts. http://www.epa.gov/seahome/housewaste/src/alum.htm. November,28 2000. Bowman, Kenneth A. World Book Encyclopedia. "Aluminum." Chicago: World Book, Inc., 1992. Cobb, Cathy. Creations of Fire. New York: Plenum Press, 1995 Geary, Don. The Welder's Bible. Pensilvania: Tab Books, 1993. Knapp PhD, Brian. Aluminum. Connecticut: Grolier, 1996. Newmark, Dr. Ann. Chemistry. London: Dorling Kindersley, 1993. Walker, John R. Modern Metalworking. Illinois: The Goodheart-Willcox Company, Inc., 1985.
A steel is usually defined as an alloy of iron and carbon with the content between a few hundreds of a percent up to about 2 wt%. Other alloying elements can amount in total to about 5 wt% in low-alloy steels and higher in more highly alloyed steels such as tool steels and stainless steels. Steels can exhibit a wide variety of properties depending on composition as well as the phases and microconstituents present, which in turn depend on the heat treatment.
As recently as six years ago, while investors were still in thrall to a dotcom bubble that had yet to burst, steel was derided as one of the last bastions of the "old" economy. Many firms in the industry were state-owned or heavily protected by governments keen to preserve assets deemed vital to national interests. Globalization had left the steel business behind. It is a measure of the changes that have swept the business since the internet bubble popped that last week Arcelor, a company created through a 2001 merger of the top French, Spanish and Luxembourg steelmakers, made a hostile bid of C$4.