Changing Oil in Your Car
When the average person's car needs an oil change we drive to a Quick Lube and have it done in 20 minutes. Another alternative would be to change the oil your self, this is a fairly simple process, most people with some common sense and some basic hand tools can do it at home on a weekend.
The first step is finding out how much oil your car holds and what kind of oil filter fits on your cars engine. Your car's owner's manual will have a capacity section in the back, down the list till you come to the engine oil capacity, and the chart will list the number of quarts that your car needs. Also on most new cars when you can look on the oil cap it should state the oil weight which is recommended by the cars manufacturer. Then you need to go to the local parts house (I prefer Advance or Orileys) get the brand of oil that you prefer in the recommended weight, and quantity. When you pay, you can get the part number for the oil filter, all you have to know is the make of the car and the motor size and they should be able to find the information and then tell you which filter belongs on the car. Remember to get an oil filter wrench to remove the filter of with if don't already have one.
Next, go home and find a level spot on which to park your vehicle. Before you jack up the front of the vehicle, you need to set the emergency brake and chock the rear wheels; this is just a safety measure to keep the car form rolling back. Once you have completed this, you need to refer to the owner's manual again for the recommended lift points for the car. You are not able to just put a jack underneath a car and lift it up because you will risk damaging the under body. There are certain places to put the jack to properly ...
... middle of paper ...
...place it in the fill hole (it is located on one of the valve cover of the motor and it has a cap) and add the recommended amount of oil. After you have added oil, replace the cap. Now you are ready to start the motor. When you first start it, there will be no oil pressure so don't be alarmed but watch the gauge, and in about ten to thirty seconds the oil pressure should be up in the normal range. With the engine running, look underneath the vehicle and check the plug and filter to make sure there are no leaks. If there are no leaks, shut the vehicle off and check the oil level on the dip stick and make sure it is between the low and full mark. If the oil is a little low, add a little more at a time, and keep rechecking it until the oil level is full. When you have completed this you are done. This is a fairly simple process and can save you a lot of money over time.
...rs and glow plugs from the valve cover gasket. Once that is done unplug the gasket from the wiring harness and remove it from the head. There is three bolts on each injector one which is holding the oil splash shield to the injector and two holding the injector to the head. To remove the injector you only have to remove the bottom bolt from the injector. then you get a pry bar and gently pry on the injector until it pops out. Install a new injector you put it in the injector cup and lightly smack it with a rubber mallet until it seats in the head.
Install the clutch cable cover. Do this now unless you have an aftermarket clutch cable that adjusts on the fork. Adjust the cable first, then put the cover on.
When the key is in the "on" position the Electronic Control Module (ECM), the main computer that controls all sensors and engine functions, powers up and readies the engine for start-up. When the starter is engaged and the coolant temperature is less than 100 degrees Fahrenheit, determined by the Coolant Temperature Sensor (CTS), the Cold Start Injector provides a spray of fuel to each cylinder via an air distribution system built into the intake manifold. If the engine temperature is greater than 100 degrees Fahrenheit, the Cold Start Injector is disabled by the cold start switch. Upon startup the ECM utilizes information in the Erasable Programmable Read Only Memory (EPROM) to establish the initial pulse rate for the fuel injectors. The ECM pulses, or opens and closes, the remaining 8 fuel injectors in sequence and the engine starts. During this, the Idle Air Control (IAC) valve is com...
Since there are so many options on the market, take several options in consideration and choose the best one according to you specific requirements. Gather all information, so you can compare in-floor with fold-out ramps and choose one according to the conditions you will be using it. If you're based in an area where it rains and snows a lot, an in-floor lift may be solution to helping you keep your interior clean. Fold-out lift may be a better option if you live in area with lots of curbs and hills.
Changing the engine oil of your car is a sure way of ensuring that your car runs well with a healthy engine. Car oil breaks and over time, the filter may become clogged with contaminants. This can take 3-24 months depending on the type of your vehicle as well as your driving habits. Luckily, changing car oil is both inexpensive and easy. You should always try to change your oil as soon as your car needs it. Below are some things that you should know before changing your own oil to make the process hassle-free.
Owning a car is usually a significant investment for an individual. Changing the oil on your car plays an important part to help keep it functioning at peak performance and to ensure that your vehicle last for many miles. You might wonder how often does the oil need changing. Well, manufactures advise that the oil is changed every 3,000 miles or every three months, whichever occurs first. Changing the oil is not an extremely difficult task, but it is always good to have someone else there, who has done this before, to help if needed. I would also suggest finding an outfit you wouldn’t mind getting dirty and a pair of rubber gloves to keep your hands clean.
A pit crew consists of two tire-carriers (front and rear), two tire-changers (front and rear), a jackman and a gasman. The rear tire changer Removes and replaces the right rear tire, using an air-powered impact wrench on the five lug nuts. He then moves to the opposite side of the car to change the left rear tire. The rear tire changer assists the rear tire changer by handing him a new tire that he's carried from behind the pit wall. He may also adjust the rear shock/jack bolt to adjust a car's handling then move to the other side to carry the other rear tire. The front tire changer and tire carrier does the same thing as the rear just on the front of the car. The jack man operates a 20-pound hydraulic jack that raises the car for tire changes. After new tires are first bolted to the right side of the car, the jackman drops the car to the ground and repeats the process on the left side. The gas man empties two 12-gallon dump cans, which weigh 81 pounds each, into the car's fuel cell. The Pit crew does all of this in under 13 seconds which is about the time it takes for one NFL play or how long it takes for you to walk to the fridge to get another beer. In an autopsy of the pit stop done by Sport Science they broke down the pit stop: The jack man gets to the car and has to precisely center the jack under a ¾ inch bolt raising the car before the tire changer removes all five lug nuts in about one second then tightening the new lug nuts in about the same speed. The entire crew explodes to the other side of the car to do the same to the driver’s side of the car. The gas man empties all 12 gallons of fuel in about five seconds. Just to put into comparison if you have ever changed a tire on the side of the road or even had the luxury of working in a shop it takes much longer to change one tire than these crews take to change all the tires and fuel up
Step 1: Remove the jack, spare tire and lug wrench. To prevent personal injury, remove the spare before raising the vehicle.
Now, assemble and arrange all of the needed supplies so that they are easily accessible. Connect the IV tubing to the solution bag and allow the fluid in the bag to run through the entire length of the tubing, also known as priming the tubing. When this is done, clamp the tubing closed. You will then need to tear several pieces of tape, six to eight inche...
Start on a small section of your car. Spray the carwash water mixture in the spray bottle on the car and pull the clay bar across your paint. What?! Yeah, don't apply any pressure just pull it across. It should slide like a hockey puck on ice. Again, place no pressure on the bar, let the bar do the work for you.
When the hood is open, look in the engine; there should be a metal loop sticking out of a metal cylinder, and that's your dipstick. Pull the dipstick out and with a rag or paper towel, wipe off the end with the oil on it off, put the stick back in, all the way and then pull it out and look where the oil ends on the end of the dipstick. If the oil doesn't reach the inside markings indicated on the end of the stick, you should add one to one-and-a-half quarts of oil, checking the level to be sure you haven't made it too full. If your oil is very dark, thick or chunky, then it is time to change your oil, and it is best to do when the engine is hot.
The primer bulbs’ purpose is to create a vacuum to pump gas to the carburetor where it will be mixed with the desired amount of air needed for optimal performance. For this reason, the primer bulb is located in close proximity to the carburetor on the saw and is also connected to the fuel tank. After the bulb is pushed six times the motor should be properly primed. The choke lever, located near the throttle, should be pushed forward to the on position. Start the chainsaw on a flat surface so it is steadied and does not come in contact with the operator’s limbs.
In this essay, I intend to go over the basics of how to jump start your car using another working vehicle. This is purely for educational purposes, and I would strongly recommended consulting a professional and your vehicle owner’s manual prior to attempting this task. As with many automobile issues, you have to have the right tools. For jump starting a car, you need jumper cables.
Place these items in the barrel and seal it. Immediately, go to the largest body of water you can find. Dump the concrete mix in the barrel and fill it with water. Let the mix harden, then reseal the bucket. Go as far into the water as you can and sink the bucket.
You ask the mechanic to call and let you know how much it will cost before doing the work. He doesn 't call and when you call him he tells you he has already done the work and your bill is 5000Mts or $100. So you need to stand out for your assertiveness.